16D2S stuck in vendor! need key out!

HomeForumsGeneral Discussion16D2S stuck in vendor! need key out!

This topic has 2 voices, contains 6 replies, and was last updated by avatar twisted247 1461 days ago.

Viewing 7 posts - 1 through 7 (of 7 total)
Author Posts
Author Posts
2012-12-04 at 08:55PM UTC #8200
avatar
TFi1969

I have had a 16D2 come to me for flashing, It was fine when i first hooked it up, was showing it’s properties fine, went to phat key it only i took to long and it timed out just as i let go of the switch on the probe and then it went into vendor mode as soon as i hit ok, i then hit outro and the properties disappeared! i hit intro and power cycled the drive and sure enough it went into vendor mode showing good flash properties, so i outo’d it again and again it disappeared! I’ve tried it on 2 different PC’s and a USBPRO but it’s the same no matter what!

Can anyone point me in the right direction on how to get the key off the drive with it in vendor mode please.
It’s not picked up by the 360 either because it’s in a vendor mode loop it seems…..

2012-12-05 at 07:28PM UTC #8202
avatar
twisted247

use dos outside of windows sounds like you erased the fw thats how a drive responds when no fw?
neway try introing it and see if it ask you for a powercycle if it doesnt and goes straight to 0×72 status then you are 4sure in vendor mode and try to use dos to outro it. good luck!!!

2012-12-05 at 08:39PM UTC #8203
avatar
TFi1969

it does only go into vedor mode after a power cycle ! not before ! i’ll give dos a go.

2012-12-06 at 01:15PM UTC #8204
avatar
twisted247

then it’s not stuck in vendor mode if it was then it wouldn’t need the powercycle when you click intro the device. do you have your jf log if so post it so i can have a look. if i understand you correctly .(you wer using phat key extract in jf you just placed the probe to mxp01 on the pcb pushed the button to extract the key then ??????? i see what you wrote but makes no sence . did you get the key ? if so no prob but i assume you didn;t and thats why the big deal i will do sum testing on a phat liteon and see if i can reproduce your situation and nail down a fix. at no time did you hit (lo-erase)?what status #’s do you get for the drive when outroing or introing it

  • This reply was modified 1462 days ago by avatar twisted247.
2012-12-06 at 01:51PM UTC #8206
avatar
twisted247

plug up the drive power it on
open jf select phat key
place probe on mpx01 then answer yes
with the probe on mpx01 still press the pmt button count to 3 release it keeping the probe on mpx01s still
it will popup telling you to remove the probe power of the drive for 5 sec the on to complete the extract.
so with the probe still on mxp01 click ok then remove the probe and hold down the pmt button count to 3 the release it and pick where to save the fw files. can’t reproduce no matter what i do got status x52 x52 x80 x90 bricked it unbricked it all with jf inside of windows . but without fw on the drive fail ever time . if you have team viewer i could take a look later on today if you wish? but the jf log will go along way to figuring this out post it if you have it k

2012-12-07 at 12:42PM UTC #8218
avatar
TFi1969

Gave up to be honest. Figured it is easiest to swap his console for another of the same type and year that’s ok. I just need to wait for 16202 to be hacked then it’s just a case of key recovery off the board.. Going to tread more carefully with these now for sure. been doing them for over a year now and this is the first to mess up..

2012-12-07 at 03:02PM UTC #8219
avatar
twisted247

it happens to the best of us at some point. good luck with it

Viewing 7 posts - 1 through 7 (of 7 total)

You must be logged in to reply to this topic.